Intel SRCU32 - RAID Controller User Manual Download Page 112 | Manualshive

Page: 112 / 182

background image

112

Intel RAID Controller SRCU32 User’s Guide

Configure Array Drives

The Configure Array Drive menu option allows you to configure array drives (hierarchy level 3).
Array drives with the following listed RAID levels can be configured within this. See Figure 54.

RAID 0

Pure Data Striping without Redundancy

RAID 1

Disk Mirroring

RAID 4

Data Striping with Dedicated Parity Drive

RAID 5

Data Striping with Striped Parity

RAID 10

RAID 0 Combined with RAID 1

Intel RAID Controller SRCU32 can manage up to 35 array drives (with different RAID levels)
simultaneously. Obviously, the number of hard drives will limit the number of parallel arrays that
can be used.

Figure 54. Select Array Drive

✏

NOTE

A RAID-1 component build will not appear on the select array drive list.

Keyboard Commands

<F4> displays level-by-level detailed information on the selected array drive (the structure, the
order, and which hard drives are part of the array drive). Use <F5> to turn on LEDs of all hard
drives belonging to this array drive. This can help to identify hard drives. If you press <Enter> on
a specific array drive StorCon displays a menu of options. See Figure 55.

Figure 55. Array Drive Menu

«
...
110
111
112
113
114
...
»

Summary of Contents for SRCU32 - RAID Controller























































































































































































Reviews:

No comments

Related manuals for SRCU32 - RAID Controller

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 5

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 2

WJMPU955 - PROCESSING UNIT - TMU

Brand: Panasonic Pages: 62

Brand: CAME Pages: 19

Brand: ICP DAS USA Pages: 48

Brand: ICP DAS USA Pages: 24

Brand: Accuphase Pages: 2

Brand: ADTRAN Pages: 2

AMB-VDX3H1 Series

Brand: Acrosser Technology Pages: 4

Linear SCP-LT8362-S-EVALZ

Brand: Analog Devices Pages: 8

Brand: HARTING Pages: 13

Brand: Idis Pages: 85

Brand: Alula Pages: 4

Brand: ZALMAN Pages: 18

Brand: Corsair Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands