Intel SRCU32 - RAID Controller User Manual Download Page 81

Page: 81 / 182

Storage Console

Uninstalling the RAID Software Suite

WARNING

Uninstalling the

RAID Software Suite

from a computer that has the operating system installed on

a host drive or pass-through disk will result in the inability to reboot the operating system. This
could result in data loss.

To remove the RAID Software Suite from Windows 2000 follow the instructions below.

1. Ensure that you have closed all applications and are logged in with administrative rights.

2. Open the Control Panel and launch the Add/Remove programs icon.

3. Select the RAID Software Suite and click “Change/Remove” for Windows 2000 or “Add/

Remove” for Windows NT.

4. The InstallShield Wizard begins.

Figure 13. Add/Remove Programs (Windows 2000 Example)

Windows 2000:

a. Select “Remove” and click “Next.”
b. A progress window appears as files are removed. (Note: The RAID device driver will not

be removed. Only the RAID software components will be removed).

c. When finished, the Maintenance Complete window is displayed. Click “Finish” to

complete the removal of the RAID software components.

Summary of Contents for SRCU32 - RAID Controller























































































































































































Search results

Summary of Contents for SRCU32 - RAID Controller

Reviews:

Related manuals for SRCU32 - RAID Controller

Brands by name

Popular brands

Intel SRCU32 - RAID Controller, User Manual

Search results

Summary of Contents for SRCU32 - RAID Controller

Reviews:

Related manuals for SRCU32 - RAID Controller

Brands by name

Popular brands