Intel SRCU32 - RAID Controller User Manual Download Page 50

Page: 50 / 182

Intel RAID Controller SRCU32 User’s Guide

3. Intel RAID Controller SRCU32 is automatically selected. Press <Enter>.

4. Complete the text-based portion of the Windows installation procedures. Reboot and continue

with the GUI-based portion of the installation.

5. After the operating system is completely installed, go to Chapter 7, Loading StorCon to

complete the installation.

Installing Windows Using the Bootable Windows CD-ROM:

1. Press <F6> as soon as the initial blue screen appears to ensure that the RAID Driver Installation

diskette can be loaded when specifying “Other.”

2. When device detection is complete, press <S> to specify additional storage devices.

3. Select “Other.” Insert the Intel RAID Controller SRCU32 Installation diskette for Windows

into the floppy drive. Press <Enter>

4. Intel RAID Controller SRCU32 is automatically selected. Press <Enter>

5. Complete the text-based portion of the Windows installation procedures. Reboot and continue

with the GUI-based portion of the installation.

6. After the operating system is completely installed, go to Chapter 7, Loading StorCon to

complete the installation.

Installing an OS onto an IDE or SCSI Hard Drive Not Attached to the Intel RAID
Controller SRCU32

Install the Intel RAID Controller SRCU32:

1. Power-off the computer.

2. Disconnect all power cords.

3. Remove the computer case to expose the server board inside. Observe all warnings and

cautions documented with the computer system to avoid shock hazards.

4. Install the Intel RAID Controller SRCU32 into an available PCI slot.

5. Replace the computer case and reconnect power cords.

6. Go to the next section for the operating system to continue the installation.

Windows 2000 / NT 4.0 Installation Procedures

✏

NOTE

This document, when referring to Windows 2000 and Windows NT, applies to the following
Windows operating systems:

•

Windows 2000 Server, Advanced Server, and Professional

•

Windows NT 4.0 Server, Enterprise Edition, Terminal Server Edition, and Workstation

Summary of Contents for SRCU32 - RAID Controller























































































































































































Search results

Summary of Contents for SRCU32 - RAID Controller

Reviews:

Related manuals for SRCU32 - RAID Controller

Brands by name

Popular brands

Intel SRCU32 - RAID Controller, User Manual

Search results

Summary of Contents for SRCU32 - RAID Controller

Reviews:

Related manuals for SRCU32 - RAID Controller

Brands by name

Popular brands