INFODRAW MRS-400 Page 5 User Manual Download

Page: 5 / 194

July 14, 2013

INFODRAW MRS-400 User Manual v5.4.1

Table of Contents

Box Contents ............................................................................................................................... 9

Required Items .......................................................................................................................... 10

Included Software ...................................................................................................................... 11

Chapter 1 - Introduction ............................................................................................................. 13

1-1 Document Scope: ............................................................................................................. 13

1-2 Terminology: .................................................................................................................... 13

1-3 Introduction: .................................................................................................................... 14

1-4 System Components: ....................................................................................................... 14

1-5 System Architecture: ........................................................................................................ 15

Chapter 2 - Hardware Interfaces ................................................................................................ 16

2-1 Video Input: ..................................................................................................................... 16

2-2 Audio: ............................................................................................................................... 16

2-3 GSM Antenna Connector: ................................................................................................ 17

2-4 GPS Antenna Connector: ................................................................................................. 17

2-5 PTZ: .................................................................................................................................. 18

2-6 GPIO: ................................................................................................................................ 18

2-7 USB Client (Mini USB Input): ............................................................................................ 19

2-8 USB Host: ......................................................................................................................... 19

2-9 Micro SD Slot: ................................................................................................................... 20

2-10 ON/OFF Switch: .............................................................................................................. 20

2-11 5V Power Input: ............................................................................................................. 20

2-12 Charging the Unit: .......................................................................................................... 21

2-13 Device Display Screen: ................................................................................................... 22

2-13-1 Device Display Menu: ...................................................................................... 22

Chapter 3 - Installation ............................................................................................................... 23

3-1 MRS Server: ...................................................................................................................... 23

3-1-1 Installing the MRS Service ................................................................................. 23

3-1-2 Installing MRS Monitor-server Application: .................................................... 26

3-2 MRS-400 Device Configuration: ....................................................................................... 29

3-2-1 MRS Device Configurator Installation:............................................................. 29

3-2-1-1 Driver Installation for Windows XP, Vista, 7 (32Bit): ....................... 32

3-2-1-2 Driver Installation for Windows 7 (64Bit):....................................... 34

3-2-1-3 Driver installation for Windows 8 OS .............................................. 38

3-2-2 Initial Configuration of the MRS Device ............................................................ 39

3-3 MRS Monitor Client: ......................................................................................................... 40

Summary of Contents for MRS-400



































































































































































































Search results

Summary of Contents for MRS-400

Reviews:

Related manuals for MRS-400

Brands by name

Popular brands

INFODRAW MRS-400, User Manual

Search results

Summary of Contents for MRS-400

Reviews:

Related manuals for MRS-400

Brands by name

Popular brands