INFODRAW MRS-400 User Manual Download

Page: 12 / 194

July 14, 2013

INFODRAW MRS-400 User Manual v5.4.1

Other included software:

Windows Mobile 5.0/ 6.0 Clients:

Used for viewing the MRS/PMRS unit’s video/ audio/ GPS streams live from your Windows
Mobile Smart Phone.

MRS USB Drivers for Windows XP, Vista and 7 (32bit):

These drivers must be installed on your PC to allow the MRS unit to connect to the Device
Configurator Program using the USB cable.

MRS USB Drivers x64 for Windows 7 (64bit):

These drivers must be installed on your PC to allow the MRS unit to connect to the Device
Configurator Program using the USB cable.

MRS ActiveX Control Software:

Used for integrating the MRS system with other control software.

MRS AV Player Application:

This application is used for viewing recorded
video/audio files. It is also used to verify recorded files
that have a digital signature assigned to them, as well
as decrypting recorded files that are encrypted with a
key.

iMRS iPhone Client:

iMRS is used for monitoring video/audio/location
streams from MRS/PMRS devices, on your iPhone.

MRS Android Client:

MRS Android Client is used for monitoring
video/audio/location streams from MRS/PMRS
devices, on your Android powered mobile device.

Summary of Contents for MRS-400



































































































































































































Search results

Summary of Contents for MRS-400

Reviews:

Related manuals for MRS-400

Brands by name

Popular brands

INFODRAW MRS-400, User Manual

Search results

Summary of Contents for MRS-400

Reviews:

Related manuals for MRS-400

Brands by name

Popular brands