manualshive.com logo in svg

INFODRAW MRS-400, User Manual

Share
Download
INFODRAW MRS-400 User Manual Download Page 29

July 14, 2013 

INFODRAW                                        MRS-400 User Manual v5.4.1                                                                        

 

 

 

29 

 

3-2   MRS-400 Device Configuration: 

The MRS-400 unit is based on embedded hardware/software with built-in cellular network 
interfaces. 

The unit must be configured prior to operation. This process includes pointing the unit’s 
connection settings to the IP address of the server. The unit is configured using the Device 
Configurator software, by connecting a USB cable between the unit and a computer (XP or 
higher). 

In order for the “

MRS device Configurator

” to work and communicate with the unit, the 

following two elements have to be installed on your PC: 

1)

 

MRS Device Configurator software. 

2)

 

MRS USB drivers.

 

 

3-2-1   MRS Device Configurator Installation: 

To setup the 

“MRS Device Configurator Application”

, follow these instructions:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1)

 

Run the 

“Setup_MRS_DeviceConfig.msi” 

file. 

2)

 

Click 

“Next”

. 

Summary of Contents for MRS-400



































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands