INFODRAW MRS-400 User Manual Download | Manualshive

Page: 19 / 194

background image

July 14, 2013

INFODRAW MRS-400 User Manual v5.4.1

19

2-7 USB Client (Mini USB Input):

The USB client is used for configuring the device’s parameters using the

Device Configurator

application. Connect the USB cable between the Mini USB Input shown here and a PC when
configuring the unit.

2-8 USB Host:

The USB host is used for external modems, disk on key, USB2LAN adapter etc.

1-6-9 SIM Card

Slot:

The SIM card slot is located on the bottom side of the unit. Turn the unit upside down (so
the back of the unit is facing upwards). Then pull the notch out carefully with your
fingernails to insert the SIM card. Once the SIM card is inserted properly, close the notch by
carefully pushing it all the way into the unit.

«
...
17
18
19
20
21
...
»

Summary of Contents for MRS-400



































































































































































































Reviews:

No comments

Related manuals for MRS-400

Brand: Pilz Pages: 16

Brand: hager Pages: 6

Brand: GRI Pages: 2

Brand: Salus Pages: 2

Brand: ABB Pages: 148

Brand: Eaton Pages: 1017

Brand: LOVATO ELECTRIC Pages: 2

Brand: iO HVAC Controls Pages: 9

Brand: Schweitzer Engineering Laboratories Pages: 568

Brand: ZooZ Pages: 2

Pro Con CVSR Series

Brand: Sterling Power Pages: 21

Brand: hitin Pages: 9

Brand: GMI Pages: 5

Brand: GMI Pages: 5

Brand: GMI Pages: 5

Brand: GMI Pages: 8

Brand: GMI Pages: 20

DUAL LITE ELCR Series

Brand: Current Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands