manualshive.com logo in svg

INFODRAW MRS-400, User Manual

Share
Download
INFODRAW MRS-400 User Manual Download Page 20

July 14, 2013 

INFODRAW                                        MRS-400 User Manual v5.4.1                                                                        

 

 

 

20 

 

2-9   Micro SD Slot: 

 

 

 

 

 

The Micro SD Slot is located on the side of the MRS unit. Insert a Micro SD card into the 
Micro SD slot for recording in the MRS device. The unit supports up to a 32GB Micro SD Card 
(SDHC). 

2-10   ON/OFF Switch: 

 

 

 

 

 

The ON/OFF Switch is located on the side of the unit. To turn the MRS-400 unit on, locate 
the ON/OFF switch on the side of the unit. An object such as a Pen Lid or small Flat Head 
Screwdriver is required. Place the object on the ridges on top of the ON/OFF switch and 

carefully

 move the switch to the ON position until it clicks and the LED lights turn on. To 

turn the unit OFF, 

carefully

 move the switch back to the OFF position until it clicks and the 

LED lights turn off. 

 

2-11   5V Power Input: 

 

 

 

 

 

The 5V power input is located on the side of the unit. Connect the 5V Power Charger here. 
DO NOT CONNECT MORE THAN 

5V

 INTO THIS INPUT. THIS WILL CAUSE DAMAGE TO THE 

UNIT.

 

Summary of Contents for MRS-400



































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands