manualshive.com logo in svg

INFODRAW MRS-400, User Manual

Share
Download
INFODRAW MRS-400 User Manual Download Page 52

July 14, 2013 

INFODRAW                                        MRS-400 User Manual v5.4.1                                                                        

 

 

 

52 

 

Automatic Bandwidth Control: 

The unit does have automatic bandwidth control which will automatically reduce the Bit 
Rate and Frame Rate of the video channel, if they are set too high for the mobile network 
bandwidth.  

 
CAUTION:

 

If the Bit Rate and Frame Rate are set excessively higher than the mobile network 
bandwidth, this may cause the unit to disconnect from the server.  

 

 

 

 

 

 

 

 

 

 

 

 

Data Usage: 

When determining the bitrate in the video parameter please consider the SIM card package 
provided to you  by your cellular provider, please consider the amount of data the unit will 
consume. The table below provides an example of a MRS-400 unit’s mobile data 
consumption when streaming continuously. 

 

Bit Rate of Steaming Video Channel:  Data Usage Per Day (roughly): 

Data Usage Per Month (roughly): 

1 channel at 100kbit/s

 

1.08 GB 

32.4 GB

 

1 channel at 200kbit/s 

2.16 GB 

64.8 GB 

1 channel at 300kbit/s 

3.24 GB 

97.2 GB 

1 channel at 400kbit/s 

4.32 GB 

129.6 GB 

 
 
 

 

The bit rate, frame rate and other 
video parameters can also be 
changed using the action menu 
(while the cursor is on the specific 
video channel).

 

Summary of Contents for MRS-400



































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands