manualshive.com logo in svg

INFODRAW MRS-400, User Manual, Page: 10 / 194

Share
Download
INFODRAW MRS-400 User Manual Download Page 10

July 14, 2013 

INFODRAW                                        MRS-400 User Manual v5.4.1                                                                        

 

 

 

10 

 

Required Items 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIM Card (Data only) 

3G/ HSPA/ EDGE/ GPRS 

Camera 

Micro SD Card 

A SIM Card (Data Only) from your 
cellular service provider is required for 
the unit. The MRS-400 unit supports 
most 3G/ HSPA/ EDGE/ GPRS SIM based 
cellular providers. The supported 
frequency bands are listed in the 
Technical Specifications section of this 
manual. 

 

Any analogue PAL/NTSC camera with a 
BNC MALE connection for video output 
can be connected to the MRS unit. The 
unit supports 1-4 cameras.   

 

A Micro SD Card is required if you would 
like to record in the MRS-400 device. 
The speed of the Micro SD Card will vary 
depending on the make. The MRS unit 
supports up to a 32GB Micro SD Card 
(SDHC).  

 

Summary of Contents for MRS-400



































































































































































































Reviews:

No comments