manualshive.com logo in svg

INFODRAW MRS-400, User Manual, Page: 17 / 194

Share
Download
INFODRAW MRS-400 User Manual Download Page 17

July 14, 2013 

INFODRAW                                        MRS-400 User Manual v5.4.1                                                                        

 

 

 

17 

 

2-3   GSM Antenna Connector: 

 

 

 

 

 

 

 

The GSM antenna has a SMA interface located near the BNC connections.  

1)

 

Twist the GSM Antenna on to the GSM Antenna Base.  

2)

 

Connect the GSM Antenna to its antenna connector shown above (Labeled 

GSM

). 

       

WARNING: 

 

Before turning the unit ON, please make sure that the GSM Antenna is connected to 
its appropriate antenna connector on the unit. If the SIM card is inserted into the 
unit and the unit is turned ON without the GSM antenna being connected, this may 
cause harm to the internal cellular modem. Therefore it is recommended to 

keep 

the GSM Antenna connected all the time

.

 

 
 

2-4   GPS Antenna Connector: 

 

 

 

 

 

 

 

The GPS antenna has a SMA interface located near the BNC connections. Connect the GPS 
antenna to the SMA GPS connector

.

 

 

GSM Antenna 

Antenna Base 

Antenna  

GPS Antenna 

Summary of Contents for MRS-400



































































































































































































Reviews:

No comments