Twinax SCS Menu
Item
Value
Description
APO
ENABLE*
DISABLE
Enables or disables automatic print orientation.
v
ENABLE—if the requested dimensions of the job fit on the paper,
the page is printed either in portrait or landscape, whichever
better fits the dimensions. If the requested dimensions do not fit
on the paper, the default orientation for the tray (COR, PORT,
LAND, or C-PORT) determines how the sheet is printed.
v
DISABLE—the page prints using the default orientation for the
tray (COR, PORT, LAND, or C-PORT).
Notes:
1. Values specified in the data stream override values set at the
printer.
2. The factory defaults (orientation set to COR and APO=ENABLE)
give you the most flexibility.
3. The requested dimensions are determined by the values of CPI,
LPI, MPP, and MPL for the job. These values can be set in the
data stream. CPI and LPI can be set on the Twinax SCS menu.
The twinax default values for MPP and MPL cannot be set from
a menu; they are 132 for MPP and 62 for MPL.
Coax Setup Menu
Use the Coax Setup Menu to configure the coax attachment. The following table
describes the settings you can change from the Coax Setup Menu. An asterisk (*)
next to a value in the table indicates the factory default. The Coax Setup Menu
appears only if you have the coax network interface card installed.
Notes:
1. To select a new value, press the Enter key when the value is displayed in the
message display area. An asterisk (*) appears next to the value in the message
display area, indicating that it is now active.
2. For more information about configuring the coax attachment, see IBM Network
Printers: Twinax/Coax Configuration Guide.
3. If you are unfamiliar with using the operator panel to work with menus, please
read “Using the Operator Panel Keys” on page 16 and “Navigating Menus” on
page 17 before continuing.
Coax Setup Menu
Item
Value
Description
PORT TMEOUT
nnn
Specifies the number of seconds the printer waits for data before it
determines there is no more data to receive for the job. The printer
then checks other installed attachments, and will switch to
attachments with jobs waiting. nnn can be from 0 to 255. The
default is 90 seconds. 0 dedicates the printer to the coax attachment
(the printer will not accept data from other attachments).
Note: If you change PORT TMEOUT from 0 to another value, you
must submit another coax job or power off and then power on the
printer before the new value can take effect.
IRQ TMEOUT
nn
Specifies when an IRQ (intervention required) timeout is sent. This
tells the printer how long to wait for an intervention required
condition to be corrected before notifying the host of the error. nn
can be from 0 to 20 minutes. The default is 1 minute. 0 specifies to
never send an IRQ timeout.
Chapter 6. Operator Panel Menus
95
Summary of Contents for InfoPrint 20
