Hyundai 2003 Tiburon Workshop Manual Download Page 54 | Manualshive

Page: 54 / 882

background image

Heavy rubber gloves (not the household type) should be worn when removing the battery.

4. Inspect the battery carrier for damage caused by the loss of electrolyte. If acid damage is present, it will be necessary to

clean the area with a solution of clean warm water and baking soda. Scrub the area with a stiff brush and wipe off with a
cloth moistened with baking soda and water.

5. Clean the top of the battery with the same solution as described in Step(4).

6. Inspect the battery case and cover for cracks. If cracks are present, the battery must be replaced.

7. Clean the battery posts with a suitable battery post cleaming tool.

8. Clean the inside surface of the terminal clamps with a suitable battery cleaning tool. Replace damaged cables and

broken terminal clamps.

9. Install the battery in the vehicle.

10. Connect the cable terminals to the battery post, making sure the tops of the terminals are flush with the tops of the

posts.

11. Tighten the terminal nuts securely.

12. Coat all connections with light mineral grease after tightening.

When batteries are being charged, an explosive gas forms beneath the cover of each cell. Do not smoke near
batteries being charged or which have recently been charged. Do not break live circuits at the terminals of
batteries being charged. A spark will occur when the circuit is broken. Keep open flames away from the battery.

Page 3 of 3

24.04.2008

http://www.hmaservice.com/viewer/content.asp?IsPrint=true&imgnum=1&print_title...

«
...
52
53
54
55
56
...
»

Summary of Contents for 2003 Tiburon



















































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 Tiburon

Brand: GMC Pages: 425

YARIS LIFTBACK 2009

Brand: Toyota Pages: 13

Brand: Westfalia Pages: 71

Brand: AA Products Pages: 6

Brand: Volvo Pages: 42

Brand: Saab Pages: 92

Brand: A-rival Pages: 23

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: ECS Pages: 4

Brand: Whispbar Pages: 15

Brand: iDataLink Pages: 6

Brand: Thule Pages: 2

Giulietta 2.0 JTDM

Brand: Alfa Romeo Pages: 14

Brand: Curt Manufacturing Pages: 4

1993 Civic Coupe

Brand: Honda Pages: 201

Brand: Or-Fab Pages: 3

Brand: Blue Ox Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands