Husqvarna TC 50 2023 Owner'S Manual Download

Page: 71 / 196

SERVICE WORK ON THE CHASSIS 11

» If the chain tension does not meet the specification:

–

Adjust the chain tension. (

p. 69)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 42)

11.41

Adjusting the chain tension

Warning

Danger of accidents

Incorrect chain tension damages components and results in accidents.

If the chain is tensioned too much, the chain, engine sprocket, rear sprocket, transmission and rear

wheel bearings wear more quickly. Some components may break if overloaded.
If the chain is too loose, the chain may fall off the engine sprocket or the rear sprocket. As a result, the

rear wheel locks or the engine will be damaged.

–

Check the chain tension regularly.

–

Set the chain tension in accordance with the specification.

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 42)

–

Check the chain tension. (

p. 68)

F02198-10

Main work
(TC 50)

–

Loosen nut

–

Loosen nuts

–

Adjust the chain tension by turning adjusting screws

left and right.
Guideline

Chain tension

5 … 8 mm (0.2 … 0.31 in)

Turn the adjusting screws

on the left and right

so that the markings on the left and right chain
adjusters

are in the same position relative to the

reference marks

. The rear wheel is then correctly

aligned.

–

Tighten nuts

–

Make sure that chain adjusters

are fitted correctly on

adjusting screws

–

Tighten nut

Guideline

Nut, rear wheel

spindle

M12x1

40 Nm (29.5 lbf ft)

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands