Husqvarna TC 50 2023 Owner'S Manual Download

Page: 130 / 196

20 TROUBLESHOOTING

128

Faults

Possible cause

Action

Engine does not speed up

The carburetor is flowing over

because the float needle is

dirty or worn

(TC 50)

–

Check/set the carburetor compo-

nents.

(TC 50 MINI)

–

Check/set the carburetor compo-

nents.

Loose carburetor jets

(TC 50)

–

Check/set the carburetor compo-

nents.

(TC 50 MINI)

–

Check/set the carburetor compo-

nents.

Fault in ignition system

–

Check the ignition system.

Engine has too little power

Fuel supply interrupted

–

Check the fuel tank breather.

–

Clean the fuel tap.

(TC 50)

–

Check/set the carburetor compo-

nents.

(TC 50 MINI)

–

Check/set the carburetor compo-

nents.

Air filter very dirty

–

Clean the air filter and air filter box.

(

p. 64)

Exhaust system leaky,

deformed or too little glass

fiber yarn filling in main

silencer

–

Check exhaust system for damage.

–

Change the glass fiber yarn filling of

the main silencer.

(

p. 65)

Ignition system defective

–

Check the ignition coil.

–

Check the spark plug connector.

Diaphragm or reed valve hous-

ing damaged

–

Check the diaphragm and reed valve

housing.

Noticeable wear

–

Overhaul the engine.

Clutch engagement speed too

low or too high

–

Check the clutch setting.

(

p. 109)

Engine stalls or is popping into

the carburetor

Lack of fuel

–

Turn the knurled screw on the fuel tap

all the way counterclockwise.

–

Refuel. (

p. 26)

Engine takes in bad air

–

Check the intake flange and carbure-

tor for tightness.

The connector or ignition coil

is loose or oxidized

–

Clean the plug-in connection and treat

it with contact spray.

Engine overheats

Too little coolant in cooling

system

–

Check the cooling system for leakage.

–

Check the coolant level. (

p. 101)

Too little air stream

–

Switch off engine when standing.

Radiator fins very dirty

–

Clean radiator fins.

Foam formation in cooling sys-

tem

–

Drain the coolant.

(

p. 101)

–

Refill with coolant.

(

p. 102)

Damaged cylinder head or

cylinder head gasket

–

Check the cylinder head or cylinder

head gasket.

Bent radiator hose

–

Change the radiator hose.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands