Husqvarna TC 50 2023 Owner'S Manual Download

Page: 165 / 196

PART 2

PRE-RIDE CHECK

Before you continue:
1. Have you determined your youngster’s readiness

to ride an OHM? Do not let your youngster ride
if you have any doubt. (Refer to the Readiness
Checklist, Part 4)

2. Have you read the owner’s manual and reviewed

it with your youngster?

3. Does your youngster fit the motorcycle properly?

4. Have you inspected the vehicle and maintained

it according to the owner’s manual?

5. Is your youngster wearing the proper protective

gear? Is the mounting procedure correct?

6. Has your youngster learned to locate the motor-

cycle controls without looking at them? Does he
or she know how to operate them smoothly?

7. Does your youngster understand that he or she

must always ride off-road?

8. Have you stressed to your youngster to keep his

or her feet on the footpegs while riding?

If you have completely covered all these areas,
you are ready to go on to Part 3.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands