Husqvarna TC 50 2023 Owner'S Manual Download

Page: 108 / 196

15 TUNING THE ENGINE

106

400192-11

–

Turn barrel adjuster

so that there is play

in the throttle

cable at the throttle grip.
Guideline

Play in throttle cable

3 … 5 mm (0.12 … 0.2 in)

–

Tighten nut

–

Slide on sleeve

Finishing work

–

Install the fuel tank.

(

p. 54)

–

Install the left side cover. (

p. 59)

–

Install the right side cover. (

p. 57)

–

Mount the seat. (

p. 62)

–

Check the play in the throttle cable. (

p. 105)

15.3

Carburetor

–

idle setting (TC 50)

K01224-10

The idle setting of the carburetor has a big influence on the

starting behavior, stable idle speed, and the response to throttle

opening. This means that an engine with a correctly set idle

speed will be easier to start than one with an incorrectly set idle

speed.

Info

The carburetor and its components are subject to

increased wear caused by engine vibration. Wear can

result in malfunctioning.

The idle speed is adjusted using the idle speed adjusting
screw

The idle mixture is adjusted using the idle air adjusting screw

15.4

Carburetor

–

idle setting (TC 50 MINI)

A00106-10

The idle setting of the carburetor has a big influence on the

starting behavior, stable idle speed, and the response to throttle

opening. This means that an engine with a correctly set idle

speed will be easier to start than one with an incorrectly set idle

speed.

Info

The carburetor and its components are subject to

increased wear caused by engine vibration. Wear can

result in malfunctioning.

The idle speed is adjusted using the idle speed adjusting
screw

The idle mixture is adjusted using the idle air adjusting screw

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands