Husqvarna TC 50 2023 Owner'S Manual Download

Page: 64 / 196

11 SERVICE WORK ON THE CHASSIS

K01168-11

(TC 50 MINI)

–

Push splash protector

to the side.

–

Position the shock absorber with screw

, depending

on the desired seating height.

–

Raise the link fork; position the shock absorber with
screw

K01167-11

–

Mount nut

and tighten the fitting.

Guideline

Screw, top

shock

absorber

M10

45 Nm (33.2 lbf ft)

Loctite

243™

–

Mount nut

and tighten the fitting.

Guideline

Screw, bot-

tom shock

absorber

M10

45 Nm (33.2 lbf ft)

Loctite

243™

–

Install the rear wheel.

(

p. 96)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 42)

11.28

Removing the seat

K00654-10

–

Open quick release

and raise the rear of the seat.

–

Pull back the seat and remove it.

11.29

Mounting the seat

K00655-10

–

Hook seat onto screw

and lower the seat at the rear and

push it forward.

Holding lug

hooks into the fuel tank.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands