Husqvarna TC 50 2023 Owner'S Manual Download

Page: 44 / 196

11 SERVICE WORK ON THE CHASSIS

11.1

Raising the motorcycle with a lift stand

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

401942-01

–

Raise the motorcycle at the frame underneath the engine.

Lift stand (80329955100)

Neither wheel is in contact with the ground.

–

Secure the motorcycle against falling over.

11.2

Removing the motorcycle from the lift stand

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

402581-10

–

Remove the motorcycle from the lift stand.

–

Remove the lift stand.

–

To park the motorcycle, insert plug-in stand

into the plug-

in stand bracket on the left side of the vehicle.

Info

Remove the plug-in stand before riding.

11.3

Bleeding the fork legs

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 42)

F02179-10

Main work
(TC 50)

–

Release bleeder screws

Any excess pressure escapes from the interior of the

fork.

–

Tighten the bleeder screws.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands