Husqvarna TC 50 2023 Owner'S Manual Download

Page: 69 / 196

SERVICE WORK ON THE CHASSIS 11

A00100-10

(TC 50 MINI)

–

Position the engine sprocket cover. Mount screws

but

do not tighten yet.

–

Mount and tighten screw

Guideline

Screw, engine

sprocket cover

15 Nm (11.1 lbf ft)

–

Tighten screws

Guideline

Screw, engine

sprocket cover

15 Nm (11.1 lbf ft)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 42)

11.38

Checking the chain for dirt

400678-01

–

Check the chain for coarse dirt accumulation.
» If the chain is very dirty:

–

Clean the chain. (

p. 67)

11.39

Cleaning the chain

Warning

Danger of accidents

Lubricants on the tires reduces the road grip.

–

Remove lubricants from the tires using a suitable cleaning agent.

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

The service life of the chain depends largely on its maintenance.

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 42)

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands