Husqvarna TC 50 2023 Owner'S Manual Download

Page: 129 / 196

TROUBLESHOOTING 20

127

Faults

Possible cause

Action

Engine turns but does not start Operating error

–

Carry out the start procedure.

(

p. 23)

Motorcycle was out of use for

a long time and there is old

fuel in the float chamber

–

Empty the carburetor float cham-

ber.

Fuel supply interrupted

–

Check the fuel tank breather.

–

Clean the fuel tap.

(TC 50)

–

Check/set the carburetor compo-

nents.

(TC 50 MINI)

–

Check/set the carburetor compo-

nents.

Spark plug sooty or wet

–

Clean and dry the spark plug and

spark plug connector, or change if

necessary.

Plug gap of spark plug too

wide

–

Adjust plug gap.
Guideline
Spark plug electrode gap
0.60 mm (0.0236 in)

Fault in ignition system

–

Check the ignition system.

Short-circuit cable in wiring

harness frayed, stop button

faulty

–

Check the stop button.

The connector or ignition coil

is loose or oxidized

–

Clean the plug-in connection and treat

it with contact spray.

Water in carburetor or jets

blocked

(TC 50)

–

Check/set the carburetor compo-

nents.

(TC 50 MINI)

–

Check/set the carburetor compo-

nents.

Engine has no idle speed

Idling jet blocked

(TC 50)

–

Check/set the carburetor compo-

nents.

(TC 50 MINI)

–

Check/set the carburetor compo-

nents.

Adjusting screws on the car-

buretor are in turned to the

wrong position

(TC 50)

–

Carburetor - adjust the idle

speed.

(

p. 107)

(TC 50 MINI)

–

Carburetor

–

adjust the idle

speed.

(

p. 108)

Spark plug defective

–

Change spark plug.

Ignition system defective

–

Check the ignition coil.

–

Check the spark plug connector.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands