Husqvarna TC 50 2023 Owner'S Manual Download

Page: 106 / 196

14 COOLING SYSTEM

104

400677-11

–

Move the vehicle into the position shown and secure it
against rolling away. Height difference

must be reached.

Guideline

Height difference

50 cm (19.7 in)

Info

For all of the air to be able to escape from the cooling

system, the vehicle must be raised at the front. If the

cooling system is poorly de-aerated, its cooling power

will be reduced and the engine may overheat.

–

Return the vehicle to the horizontal position.

–

Add coolant to level

–

Mount the radiator cap.

Finishing work

–

Go for a short test ride.

–

Check the cooling system for leaks.

–

Check the coolant level. (

p. 101)

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands