Husqvarna TC 50 2023 Owner'S Manual Download

Page: 50 / 196

11 SERVICE WORK ON THE CHASSIS

11.10

Installing the lower triple clamp

F02885-10

Main work

–

Clean the bearing and sealing elements, check for damage,

and grease.

High viscosity grease (

p. 139)

–

Insert the lower triple clamp with the steering stem. Mount
upper steering head bearing

–

Check whether upper steering head seal

is correctly posi-

tioned.

–

Push on protective ring

V02097-10

–

Position the upper triple clamp with the handlebar.

–

Mount nut

, but do not tighten it yet.

F02179-11

(TC 50)

–

Position the fork legs.

Bleeder screws

are positioned toward the rear.

Info

The second milled groove (from the top) must

be flush with the upper edge of the upper triple

clamp.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands