Husqvarna TC 50 2023 Owner'S Manual Download

Page: 121 / 196

CARBURETOR 17

119

Preparatory work

–

Turn the knurled screw on the fuel tap all the way clockwise.

R04503-10

Main work

–

Pull off fuel hose

Info

Remaining fuel may flow out of the fuel hose.

R04485-10

–

Loosen hose clip

–

Loosen hose clip

R04502-10

–

Push back hose clamp

and pull off the vent hose.

–

Pull the carburetor out of the intake flange.

–

Pull the carburetor forward out of the inlet sleeve.

R04487-10

–

Remove throttle slide cover

–

Pull the throttle slide out of the carburetor.

–

Drain the remaining fuel.

R04504-10

–

Pull back the spring retainer and throttle slide spring.

–

Detach throttle cable wire

–

Take off the throttle slide.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands