Husqvarna TC 50 2023 Owner'S Manual Download Page 85

Page: 85 / 196

BRAKE SYSTEM 12

F02237-10

–

Remove lock ring

–

Loosen screw

–

Remove screw

and

–

Press back the brake linings by slightly tilting the brake

caliper laterally on the brake disc. Carefully pull the brake

caliper backward from the brake disc.

–

Remove screw

Warning

Danger of accidents

Oil or grease on the brake

discs reduces the braking effect.

–

Always keep the brake discs free of oil and

grease.

–

Clean the brake discs with brake cleaner when

necessary.

–

Check the brake discs. (

p. 78)

V00553-10

–

Remove the brake linings.

–

Clean the brake caliper and the brake caliper bracket.

–

Press the brake piston back into the basic position and

ensure that brake fluid does not flow out of the brake fluid

reservoir; extract some if necessary.

V00553-11

Warning

Danger of accidents

Brake linings which have not

been approved alter the braking efficiency.

Not all brake linings are tested and approved for

Husqvarna motorcycles. The structure and friction

coefficient of the brake linings, and thus their brake

power, may vary greatly from that of original brake

linings.
If brake linings are used that differ from the original

equipment, compliance with the original homologa-

tion is not guaranteed. In this case, the vehicle no

longer corresponds to its condition at delivery and

the manufacturer warranty shall be void.

–

Only use brake linings approved and

recommended by Husqvarna motorcycles.

–

Position the new brake linings.

Info

Always change the brake linings in pairs.
Ensure that the brake linings are correctly positioned

in the holding spring.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Husqvarna TC 50 2023, Owner'S Manual, Page: 85 / 196

Search results

Summary of Contents for TC 50 2023

Reviews: