Husqvarna TC 50 2023 Owner'S Manual Download

Page: 66 / 196

11 SERVICE WORK ON THE CHASSIS

11.32

Cleaning the air filter and air filter box

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Do not clean the air filter with fuel or petroleum since these substances attack the foam.

Preparatory work

–

Remove the seat. (

p. 62)

–

Remove the air filter.

(

p. 63)

M01514-01

Main work

–

Wash the air filter thoroughly in special cleaning liquid and

allow it to dry properly.

Air filter cleaner (

p. 139)

Info

Only press the air filter to dry it, never wring it out.

–

Oil the dry air filter with a high-grade air filter oil.

Oil for foam air filter (

p. 139)

–

Clean the air filter box.

–

Check intake flange for damage and looseness.

Finishing work

–

Install the air filter.

(

p. 63)

–

Mount the seat. (

p. 62)

11.33

Removing the main silencer

Warning

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

–

Allow the exhaust system to cool down before performing any work on the vehicle.

Preparatory work

–

Remove the seat. (

p. 62)

–

Remove the right side cover. (

p. 56)

K00673-10

Main work

–

Remove screw

–

Remove screw

–

Pull off the main silencer from the manifold at sleeve

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands