Husqvarna TC 50 2023 Owner'S Manual Download

Page: 111 / 196

TUNING THE ENGINE 15

109

15.7

Checking the clutch setting

V00541-10

–

Connect special tool

Tachometer (45129075000)

401521-01

–

Let the front wheel of the vehicle make contact with a fixed

object.

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and

death.

–

Always make sure there is sufficient ventilation

when running the engine.

–

Use effective exhaust extraction when starting or

running the engine in an enclosed space.

–

Start the motorcycle.

–

Only ride full throttle to the point where the maximum engine

speed is reached.
Guideline

Operation at full throttle

≤

3 s

–

Read the speed.

Slip speed

8,700 … 9,300 rpm

» If the specified value is not reached:

–

Adjust the clutch.

(

p. 110)

15.8

Removing the clutch cover

Note

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to enter the groundwater, the soil, or the sewage system.

Info

Fuel can emerge via the carburetor.
Capture emerging fuel using a suitable container.

–

Turn the knurled screw on the fuel tap all the way clockwise.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands