Huawei RU3632 Installation Manual Download Page 59

Page: 59 / 128

RRU3832&RRU3632
Installation Guide

8 Installing the RU

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Installing the RU

About This Chapter

This chapter describes the procedure for installing the RU. The procedure for installing the
RU varies depending on installation options.

8.1 Mounting Kits for an RU

This section describes the bracket assembly and the attachment plate for an RU.

8.2 Installing the RU on a Pole

One or more RUs can be installed on a pole.

8.3 Installing the RU on U-steel

This section describes the procedure and precautions for installing the RU on U-steel. An RU
can be installed on U-steel secured on the ground or a tower. Each piece of U-steel allows
only one RU to be installed in standard or reverse mode.

8.4 Installing the RU on Angle Steel

This section describes the procedure and precautions for installing the RU on angle steel. An
RU can be installed on angle steel secured on the ground or a tower. Each piece of angle steel
allows only one RU to be installed in standard or reverse mode.

8.5 Installing the RU on a Wall

This section describes the procedure and precautions for installing the RU on a wall.

8.6 Installing an RU on an IFS06

This section describes the procedure and precautions for installing an RU on an IFS06.

8.1 Mounting Kits for an RU

This section describes the bracket assembly and the attachment plate for an RU.

Figure 8-1

shows the front and side of an RU.

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands