Huawei RU3632 Installation Manual Download Page 73

Page: 73 / 128

RRU3832&RRU3632
Installation Guide

8 Installing the RU

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential



Do not stand the RU upright because the RF ports cannot support the weight of the RU.



Place a foam pad or cardboard under the RU to protect the RU housing from damage
during the installation.

Context

Figure 8-20

shows the top view of the RU installed on U-steel.

When the width of the narrower edges of the U-steel is less than 40 mm (1.57 in.), only the a
and b modes are supported.

Figure 8-20

Top view of the RU

(1) U-steel

Procedure

Step 1

Determine a position for installing the mounting brackets.



If the RU must be installed on U-steel secured on a tower, see

3.5.1 Clearance for a

Single RU

to determine a position.



If the RU must be installed on U-steel secured on the ground, see

Figure 8-21

determine a position.

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands