Huawei RU3632 Installation Manual Download Page 10

Page: 10 / 128

RRU3832&RRU3632
Installation Guide

1 Changes in the RU3832&RU3632 Installation Guide

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Changes in the RU3832&RU3632

Installation Guide

This chapter describes the changes in the

RU3832&RU3632 Installation Guide

05 (2014-06-30)

This is the fifth official release.

Compared with issue 04 (2013-12-30), this issue includes the following change:

Topic

Change Description

3.5.1 Clearance for a Single RU

Added the clearance for a single RU or
multiple RUs on the bitumen ground.

3.5.2 Clearances for Three or More RUs

9.8 Installing an RU Alarm Cable

Added notes under the procedure.

3.4 Installation Scenarios

Added restrictions on RU mounting kits in
assembled installation mode.

Compared with issue 04 (2013-12-30), this issue does not include any new information and no
information is deleted from this issue.

04 (2013-12-30)

This is the fourth official release.

Compared with issue 03 (2013-12-23), this issue includes the following change:

Topic

Change Description

3.4 Installation Scenarios

Modified the figure showing the U-steel
specifications.

Compared with issue 03 (2013-12-23), this issue does not include any new information and no
information is deleted from this issue.

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands