Huawei RU3632 Installation Manual Download Page 3

Page: 3 / 128

RRU3832&RRU3632
Installation Guide

About This Document

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

About This Document

Purpose

This document describes the process of installing DC blade RU3832 and RU3632 (referred to
as RU in this document).

Product Versions

The following table lists the product versions related to this document for RU3832.

Product Name

Solution Version

Product Version

DBS3900

SRAN6.0 and later versions

V100R004C00 and later
versions

RAN13.0 and later versions

V200R013C00 and later
versions

eRAN6.0 and later versions

V100R006C00 and later
versions

The following table lists the product versions related to this document for RU3632.

Product Name

Solution Version

Product Version

DBS3900



SRAN8.0 and later
versions



eRAN6.0 and later
versions

V100R008C00 and later
versions

Intended Audience

This document is intended for:

Base station installation engineers

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands