Huawei RU3632 Installation Manual Download Page 34 | Manualshive

Page: 34 / 128

background image

RRU3832&RRU3632
Installation Guide

3 Information About the Installation

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

25

If an RU is installed on the bitumen ground, the RU must be at least 500 mm (700 mm or
more as recommended) away from the bitumen ground. The following describes the space
requirements for installing a single RU on the non-bitumen ground.



The recommended clearance ensures normal running and provides an appropriate space for
operation and maintenance (OM). If there is sufficient space, leave the recommended clearance after
installing the equipment.



The minimum clearance ensures normal running and heat dissipation, but OM activities such as
checking indicator status and opening the cabling cavity cannot be properly conducted. If the
installation space is restricted, leave the minimum clearance after installing the equipment.

Clearance for a Single RU in Standard or Reverse Mode

shows the clearance for a single RU in standard or reverse mode.

«
...
32
33
34
35
36
...
»

Summary of Contents for RU3632

































































































































Reviews:

No comments

Related manuals for RU3632

Brand: Paradyne Pages: 16

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

Brand: LaCie Pages: 4

Brand: LaCie Pages: 4

Brand: Zonet Pages: 10

Brand: Samsung Pages: 65

Brand: Industrex Pages: 51

EK-FB GA AX370 Gaming RGB Monoblock

Brand: ekwb Pages: 2

Brand: u-blox Pages: 29

Brand: ANEP Pages: 48

Brand: NEC Pages: 70

Comet 3356P-LAN

Brand: ZyXEL Communications Pages: 38

HFisolator 9730/26-11

Brand: Stahl Pages: 2

OPTIMA II CNPS10X

Brand: ZALMAN Pages: 20

Wisenet XRN-6410DB4

Brand: Hanwha Techwin Pages: 118

EdgeRouter X ER-X-SFP

Brand: Ubiquiti Pages: 20

Brand: l-com Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands