Huawei RU3632 Installation Manual Download Page 4

Page: 4 / 128

RRU3832&RRU3632
Installation Guide

About This Document

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

iii

Organization

1 Changes in the RU3832&RU3632 Installation Guide

This chapter describes the changes in the

RU3832&RU3632 Installation Guide

2 Installation Preparations

This chapter describes the reference documents, tools, and instruments that must be ready
before the installation. In addition, it specifies the skills and prerequisites that installation
engineers must have.

3 Information About the Installation

Before installing an RU, you must be familiar with its exterior, ports, indicators, installation
options and installation clearance requirements.

4 Unpacking the Equipment

This chapter describes how to unpack and check the delivered equipment to ensure that all the
materials are included and intact.

5 Installation Process

The installation process involves installing an RU and RU cables, checking the RU hardware
installation, and powering on the RU.

6 (Optional) Installing the Plastic Shells of the RU

This section describes the procedure for installing the plastic shells of the RU.

7 Hoisting an RU and Related Cables onto a Tower

This section describes the procedure for hoisting an RU and related cables onto a tower and
the precautions that must be taken.

8 Installing the RU

This chapter describes the procedure for installing the RU. The procedure for installing the
RU varies depending on installation options.

9 Installing RU Cables

This chapter describes the procedure for installing RU cables.

10 Checking the RU Hardware Installation

After an RU is installed, check the hardware installation.

11 Powering On an RU

After all the devices are installed, check the power-on status of an RU.

12 Appendix

This section describes the procedure for adding an easy power receptacle (pressfit type)
connector.

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands