Huawei RU3632 Installation Manual Download Page 38 | Manualshive

Page: 38 / 128

background image

RRU3832&RRU3632
Installation Guide

3 Information About the Installation

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

29

If an RU is installed on the bitumen ground, the RU must be at least 500 mm (700 mm or
more as recommended) away from the bitumen ground. The following describes the space
requirements for installing multiple RUs on the non-bitumen ground.



The recommended clearances ensure normal running and provide an appropriate space for operation
and maintenance (OM). If there is sufficient space, retain the recommended clearances.



The minimum clearances ensure normal running and heat dissipation but do not allow OM activities
such as checking indicator status and opening the cabling cavity. If the installation space is
insufficient, retain the minimum clearances after the installation.

Recommended Clearances for Three or More RUs Installed on a Pole

shows the recommended clearances for multiple RUs installed in centralized

mode.

Figure 3-28

Recommended clearances for three or more RUs installed on a pole

Minimum Clearances for Three or More RUs Installed on a Pole

shows the minimum clearances for multiple RUs installed in centralized mode.

«
...
36
37
38
39
40
...
»

Summary of Contents for RU3632

































































































































Reviews:

No comments

Related manuals for RU3632

Brand: Salus Pages: 16

Brand: Acqiris Pages: 22

Brand: FOR-A Pages: 2

tBOX330-870-FL Series

Brand: AXIOMTEK Pages: 2

Brand: Funkwerk Pages: 2

Brand: Waves Pages: 41

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

Brand: Xmart Pages: 8

Brand: TP-Link Pages: 176

Low Power Series

Brand: FabiaTech Pages: 77

Brand: Cowfish Technologies Pages: 38

CNPS11X Extreme

Brand: ZALMAN Pages: 12

Brand: MICROENER Pages: 24

IP-Logic ZIG-IPPRO-RX

Brand: Zigen Pages: 4

Brand: Tripp Lite Pages: 3

Brand: ADS Technologies Pages: 1

Brand: CSL Pages: 24

Brand: Avigilon Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands