Huawei RU3632 Installation Manual Download Page 78

Page: 78 / 128

RRU3832&RRU3632
Installation Guide

8 Installing the RU

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Figure 8-28

Distance between the mounting brackets and the ground

It is recommended that the mounting brackets be installed at a height of 1200 mm (47.24 in.) to 1600
mm (62.99 in.) above the ground.

Step 2

Install the RU mounting brackets, as shown in

Figure 8-29

Figure 8-29

Installing the RU mounting brackets

Verify that the arrows on the mounting brackets are pointing up.

Adjust the position of the nut and remove one end of the square-neck bolt from the slot
on the auxiliary bracket.

Slide the mounting brackets onto the angle steel horizontally and insert the square-neck
bolt into the slot.

Step 3

Use a 16 mm (0.67 in.) M10 torque wrench to tighten the nuts to 40 N·m (354.03 lbf·in.) so
that the mounting brackets are secured onto the angle steel, as shown in

Figure 8-30

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands