Huawei RU3632 Installation Manual Download Page 25

Page: 25 / 128

RRU3832&RRU3632
Installation Guide

3 Information About the Installation

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Figure 3-8

Requirements for the vertical deviation angle of an RU

(1) RU

(2) Installation support (pole, U-steel, angle steel, or wall)

Installing an RU on a Pole

Figure 3-9

shows the diameter of a pole for installing an RU.

Figure 3-9

Diameter of a pole



The diameter of a pole for installing an RU ranges from 60 mm (2.36 in.) to 114 mm (4.49
in.). The recommended diameter is 80 mm (3.15 in.).



When the diameter of a pole ranges from 60 mm (2.36 in.) to 76 mm (2.99 in.), a
maximum of three RUs can be installed on the pole and the side-mounted installation is
recommended.



Only a pole whose diameter ranges from 76 mm (2.99 in.) to 114 mm (4.49 in.) supports
more than three RUs.



The recommended thickness of the wall of a pole is 3.5 mm (0.14 in.) or above.

Figure 3-10

shows a single RU installed on a pole.

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands