Huawei RU3632 Installation Manual Download Page 44

Page: 44 / 128

RRU3832&RRU3632
Installation Guide

4 Unpacking the Equipment

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Unpacking the Equipment

This chapter describes how to unpack and check the delivered equipment to ensure that all the
materials are included and intact.

Context

When transporting, moving, or installing the equipment, components, or parts, you must:



Prevent them from colliding with doors, walls, shelves, or other objects.



Wear clean gloves, and avoid touching the equipment, components, or parts with bare hands,
sweat-soaked gloves, or dirty gloves.



After a cabinet or an BBU is unpacked, it must be powered on within 7 days.



After an RU is unpacked, it must be powered on within 24 hours.

Procedure

Step 1

Check the total number of articles in each case according to the packing list.

If ...

Then ...

The total number tallies with the
packing list

Go to

Step 2

The total number does not tally with
the packing list

Find out the cause and report any missing
articles to the local Huawei office.

Step 2

Check the exterior of the packing case.

If ...

Then ...

The outer packing is intact

Go to

Step 3

The outer packing is severely
damaged or soaked

Find out the cause and report it to the local
Huawei office.

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands