Huawei RU3632 Installation Manual Download Page 22

Page: 22 / 128

RRU3832&RRU3632
Installation Guide

3 Information About the Installation

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Figure 3-6

Recommended usage of the RF ports on RU3832 and RU3632 used for DBS3900 LTE

V100R006C00 and later versions

3.3 RU Indicators

This section describes six indicators on an RU. They indicate the running status.

For detailed positions of RU indicators, see

3.2 RU Ports

Table 3-4

describes RU indicators.

Table 3-4

RU indicators

Indicator

Color

Status

Meaning

RUN

Green

Steady on

There is power supply, but the module is
faulty.

Steady off

There is no power supply, or the module is
faulty.

Blinking (on for
1s and off for 1s)

The board is functioning properly.

Blinking (on for
0.125s and off for
0.125s)

Software is being loaded to the module, or
the module is not started.

ALM

Red

Steady on

Alarms are generated, and the module must
be replaced.

Blinking (on for
1s and off for 1s)

Alarms are generated. The alarms may be
caused by the faults on the related boards or
ports. Therefore, you need to locate the
fault before deciding whether to replace the
module.

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands