Huawei RU3632 Installation Manual Download Page 111

Page: 111 / 128

RRU3832&RRU3632
Installation Guide

9 Installing RU Cables

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

102

Route the cables according to the instructions in

9.1 Cabling Requirements

, and then use

cable ties to bind the cables.

Label the installed cables according to the instructions in Attaching an L-Shaped Label.

----End

9.8 Installing an RU Alarm Cable

This section describes the procedure for installing an RU alarm cable.

Procedure

Step 1

Use an M3 Phillips screwdriver to loosen the screws on the dustproof cap on the EXT_ALM
port and remove the dustproof cap.

Step 2

Connect the waterproof DB15 connector at one end of the RU alarm cable to the EXT_ALM
port on the RU, as shown in

Figure 9-19

Figure 9-19

Installing an RU alarm cable

Install the waterproof DB15 male connector on the RU alarm cable with caution, preventing the pin
assignment from being damaged.

Step 3

Use an M3 Phillips screwdriver to tighten the posts on both sides of the waterproof DB15
male connector to 0.4 N·m (3.54 lbf·in.).

Step 4

Connect the eight cord end terminals at the other end to external alarm devices.

Use insulating adhesive tapes to wrap cord end terminals that are not in use and fix them at a proper
position based on the onsite situations. This prevents false alarm reporting and equipment damage due to
contact of exposed cables.

Figure 9-20

shows the method for handling cord end terminals not in use.

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands