Huawei RU3632 Installation Manual Download Page 61

Page: 61 / 128

RRU3832&RRU3632
Installation Guide

8 Installing the RU

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

8.2 Installing the RU on a Pole

One or more RUs can be installed on a pole.

8.2.1 Installing a Single RU

This section describes the procedure and precautions for installing a single RU on a pole.

Prerequisites

Before you install an RU on a pole secured on a tower, the RU and its mounting brackets are
hoisted onto the tower. For details, see

7.1 Hoisting an RU onto a Tower

The hoist clamp on the main bracket is secured properly.



Do not stand the RU upright because the RF ports cannot support the weight of the RU.



Place a foam pad or cardboard under the RU to protect the RU housing from damage
during the installation.

Procedure

Step 1

Determine a position for installing the mounting brackets.



If the pole must be installed on a tower, determine a position for installing the mounting
brackets according to the instructions in

3.5.1 Clearance for a Single RU



If the pole must be installed on the ground, determine a position for installing the
mounting brackets according to

Figure 8-3

Figure 8-3

Distance between the mounting brackets and the ground

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands