Huawei IDS1000 User Manual Download Page 40

Page: 40 / 67

IDS1000 Container Data Center
User Manual

5 Alarm Reference

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

Alarm Reference

Alarm

Alarm
Severit
y

Alarm
Type

Impact on the
System

Solution

Gas
extinguish
ing
controller
communic
ation
failure

Critical

Event

The fire
extinguishing
system cannot
be monitored.

See the documents delivered with the
gas extinguishing controller.

Fire
extinguish
ing
hardware
fault

Critical

Event

The fire
extinguishing
system does not
work.

Check whether the fire
extinguishing components are in
good condition and properly
connected.



If yes, contact Huawei
technical support.



If no, go to

Rectify the fault and check
whether the alarm is cleared.



If yes, no further action is
required.



If no, contact Huawei technical
support.

Fire
extinguish
ing
triggered

Critical

Alarm

The fire
extinguishing
equipment has
released
extinguishing
agents into the
protected zone
of the container.

Check whether a fire is present in the
container.

If yes, fire extinguishing cylinders are
triggered. Wait for the fire
extinguishing system to respond.

If no, check whether fire
extinguishing cylinders are triggered.



If the fire extinguishing cylinders
are triggered, press the shutdown
button on the emergency
startup/abort switch to stop fire

Summary of Contents for IDS1000




































































Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands

Huawei IDS1000, User Manual

Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands