Huawei IDS1000 User Manual Download Page 49

Page: 49 / 67

IDS1000 Container Data Center
User Manual

6 Troubleshooting

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

6.6 Failed to Drive the Fire Cylinder

Possible Causes



The gas cylinder is not driven successfully.



Cable connection of the gas cylinder is abnormal.

Tools and Materials



Gloves



Multimeter



Screwdriver

Procedure

Step 1

Check whether the gas cylinder is driven successfully.

Y => Contact Huawei technical support.

N => Go to

Step 2

Step 2

Replace the driving device of the gas cylinder.

Check whether the fault is rectified.

Y => No further action is required.

N => Contact Huawei technical support.

----End

6.7 VESDA Fault

For details about how to rectify VESDA faults, see the documents delivered with the VESDA
or contact Huawei technical support.

6.8 Gas Extinguishing Controller Fault

Possible Causes



The gas extinguishing controller is not properly connected.



The gas extinguishing controller is faulty.

Tools and Materials



Documents delivered with the gas extinguishing controller



Screwdriver



Gloves



Dedicated keys to the controller box

Summary of Contents for IDS1000




































































Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands

Huawei IDS1000, User Manual

Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands