Huawei IDS1000 User Manual Download Page 62 | Manualshive

Page: 62 / 67

background image

IDS1000 Container Data Center
User Manual

8 Emergency Operation

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

56

8

Emergency Operation

About This Chapter

When a critical alarm or fault occurs during the O&M of the fire extinguishing system in the
container data center, rectify the fault by referring to the emergency operation guide in this
chapter.

8.1 Early Fire Alarm

Prerequisites

An early fire alarm is generated in the data center.

The emergency operations described in this section are for reference only.

If an early fire alarm is generated, determine whether to extinguish the fire or leave the area
immediately based on actual situation and contact the personnel on duty or local fire station.

Procedure

Step 1

Locate the fire alarm area based on the alarm information.

Step 2

Go to the area with necessary personal protective equipment (PPE) and communications
devices.

Do not enter the fire alarm area without determining the severity and impact of the fire.

Step 3

Observe the gas release indicator to check whether gas is released to extinguish the fire.

«
...
60
61
62
63
64
...
»

Summary of Contents for IDS1000




































































Reviews:

No comments

Related manuals for IDS1000

Brand: Eaton Pages: 166

Brand: Baader Planetarium Pages: 7

Brand: Beaphar Pages: 2

PROFINET BNI PNT-508-055-P067

Brand: Balluff Pages: 84

Max Charge MC-624

Brand: Balmar Pages: 8

MAX CHARGE MC-614

Brand: Balmar Pages: 20

Brand: Eaton Pages: 8

Brand: U.S. Divers Pages: 22

Brand: Nemesis Pages: 6

Brand: Aeta Audio Systems Pages: 24

Brand: Reer Pages: 2

Brand: M-system Pages: 7

Brand: IDEATEC Pages: 32

Brand: Broadcast Tools Pages: 15

Q.PEAK DUO XL-G11S.X / BFG Series

Brand: Qcells Pages: 26

Brand: EpiSensor Pages: 37

Brand: Potter Pages: 25

Brand: Nolan Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands