Huawei IDS1000 User Manual Download Page 38

Page: 38 / 67

IDS1000 Container Data Center
User Manual

4 Routine Maintenance

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

4.6 Semi-Yearly Maintenance

Maintena
nce Item

Operation

Expected
Result

Troubleshooting

VESDA air
detector
network

Check the connection of
air detectors.

The air detectors
are securely
connected.

Connect the air detectors
securely.

Smoke
detectors

Use a dedicated test
instrument or a smoke
generator to blow
smoke to a smoke
detector and check the
indicator status on the
smoke detector.



If the smoke
density is
below the
alarm
threshold, the
alarm
indicator
blinks once
every six
seconds.



If the smoke
density
exceeds the
alarm
threshold, the
alarm
indicator is
steady on.



If the smoke density is
below the alarm threshold
but the alarm indicator
blinks twice every six
seconds, the smoke
detector is faulty. Replace
the smoke detector.



If the smoke density
exceeds the alarm
threshold but the alarm
indicator is not steady on,
replace the smoke
detector.

For details about how to
replace a smoke detector, see

7.1 Replacing a Smoke
Detector

NOTE

You are advised to clean smoke
detectors every two years.

Heat
detectors

Use a dedicated test
instrument or a blow
drier to check the heat
detectors. Observe the
alarm indicator.

NOTICE

To prevent damage to the
heat detector probe, keep
a proper distance between
the sensor probe and the
blower drier.



If the
temperature
is below the
alarm
threshold, the
alarm
indicator is
blinking.



If the
temperature
exceeds the
alarm
threshold, the
alarm
indicator is
steady on.



If the temperature is
below the alarm threshold
but the alarm indicator is
steady on, replace the
heat detector.



If the temperature
exceeds the alarm
threshold but the alarm
indicator is not steady on
(that is, no alarm is
generated), replace the
heat detector.

For details about how to
replace a heat detector, see

7.2 Replacing a Heat
Detector

Summary of Contents for IDS1000




































































Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands

Huawei IDS1000, User Manual

Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands