Huawei IDS1000 User Manual Download Page 45 | Manualshive

Page: 45 / 67

background image

IDS1000 Container Data Center
User Manual

6 Troubleshooting

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

39



1: L2 (connected to the common terminal)



2: L1 (connected to a lower-level device)



3: L1 (connected to an upper-level device)



4: reserved

Use a multimeter to check whether there is any short circuit or open circuit.

Y => Rectify the connection fault.

Check whether the fault is rectified.



If yes, no further action is required.



If no, contact Huawei technical support.

N => Contact Huawei technical support.

----End

6.3 Gas Release Indicator Fault

Possible Causes



The power supply to the gas release indicator is abnormal.



The gas release indicator is faulty.



The cable connection of the gas release indicator is abnormal.

Tools and Materials



Multimeter



Gloves



Screwdriver



Step ladder

Procedure

Step 1

Check the power supply to the gas release indicator.

Short circuit the pressure annunciator after the cable is removed from the solenoid valve.
When the gas release indicator is off, use a multimeter to measure the two terminals (24 V+
and GND) of the gas release indicator. Check whether the voltage is within the normal range.

Y => Go to

N => Regulate the voltage to a normal value.

Check whether the fault is rectified.



If yes, no further action is required.



If no, go to

Step 2

Replace the gas release indicator.

Check whether the fault is rectified.

If yes, no further action is required.

«
...
43
44
45
46
47
...
»

Summary of Contents for IDS1000




































































Reviews:

No comments

Related manuals for IDS1000

Brand: S&C Pages: 40

Brand: S&C Pages: 34

Brand: GARDTEC Pages: 48

Brand: FAAC Pages: 64

Brand: Aaeon Pages: 76

Brand: HandyTrac Pages: 14

Brand: TA Pages: 6

Brand: Eaton Pages: 8

Brand: NAiS Pages: 144

Brand: WAGO Pages: 16

ArmorBlock 1732E-16CFGM12R

Brand: Allen-Bradley Pages: 20

Brand: Integral Pages: 7

Brand: select solar Pages: 2

Brand: TCS Pages: 8

Brand: Raypak Pages: 2

Brand: 4D systems Pages: 6

Brand: MONSTER MOBILE Pages: 22

Brand: Phoenic Mecano Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands