Huawei IDS1000 User Manual Download Page 59

Page: 59 / 67

IDS1000 Container Data Center
User Manual

7 Parts Replacement

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

Procedure

Step 1

Remove the gas extinguisher to be replaced.

Step 2

Install a new gas extinguisher and attach a label to it.

----End

Follow-up Procedure

Send the faulty gas extinguisher together with a

Repair Notice

to your local Huawei office for

repair.

7.8 Replacing the Emergency Start/Abort Switch

Prerequisites



The emergency start/abort switch is faulty.



Spare emergency start/abort switches are available.

Tools and Materials



Phillips screwdriver



Flat-head screwdriver



Spare emergency start/abort switches



Key to the control box



Gloves

Impact on the System

None

Procedure

Step 1

Use a Phillips screwdriver to remove the screws from the emergency start/abort switch.

Summary of Contents for IDS1000




































































Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands

Huawei IDS1000, User Manual

Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands