Huawei IDS1000 User Manual Download Page 25

Page: 25 / 67

IDS1000 Container Data Center
User Manual

3 Power-On Commissioning

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

Before the power-on of the container data center fire extinguishing system, check all the fire
extinguishing components one by one by following the preceding check methods and items.

----End

3.3 Hardware Power-On Commissioning

Prerequisites



You have completed the power-on check.



You have obtained the

Container Data Center Initial Configuration Guide

and

Container

Data Center Power-On Commissioning Guide



You have obtained the documents delivered with the fire extinguishing devices.

Procedure

Step 1

Switch on the input circuit breaker for the VESDA power box in the corresponding protected
zone. For details, see the

Container Data Center Initial Configuration Guide

and

Container

Data Center Power-On Commissioning Guide

Step 2

Complete the power-on commissioning for the VESDA. For details, see the delivered
VESDA documents.

If multiple VESDAs are configured in the protected zone, follow the preceding power-on
operations to power on their hardware.

Step 3

Switch on the input circuit breaker for the gas extinguishing controller in the corresponding
protected zone. For details, see the

Container Data Center Initial Configuration Guide

and

Container Data Center Power-On Commissioning Guide

Step 4

Turn on the main power and backup power switches for the controller to power on the gas
extinguishing controller.

Figure 3-11

shows the positions of the switches.

Summary of Contents for IDS1000




































































Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands

Huawei IDS1000, User Manual

Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands