Huawei IDS1000 User Manual Download Page 55

Page: 55 / 67

IDS1000 Container Data Center
User Manual

7 Parts Replacement

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

Step 4

Power on the gas fire extinguishing controller.

Step 5

If the red indicator on the heat detector blinks every 6 seconds, the heat detector is working
properly.

Step 6

Check that the new heat detector is working properly.

----End

Follow-up Procedure

Send the faulty heat detector together with a

Repair Notice

to your local Huawei office for

repair.

7.3 Replacing a Gas Release Indicator

Prerequisites



A gas release indicator is faulty.



Spare gas release indicators are available.

Tools and Materials



Phillips screwdriver



Spare gas release indicators



Gloves



Step ladder



Key to the control box

Impact on the System

None

Procedure

Step 1

Use to screwdriver to loosen the screws that fasten the gas release indicator with its base and
remove the gas release indicator.

Step 2

Connect the cable to a new gas release indicator regardless of the polarity.

Step 3

Check that the new gas release indicator is working properly.

----End

Follow-up Procedure

Send the faulty gas release indicator together with a

Repair Notice

to your local Huawei office

for repair.

Summary of Contents for IDS1000




































































Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands

Huawei IDS1000, User Manual

Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands