Huawei IDS1000 User Manual Download Page 43

Page: 43 / 67

IDS1000 Container Data Center
User Manual

6 Troubleshooting

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

Figure 6-1

shows the positions and functions of terminals on the sensor base.

Figure 6-1

Terminals on the sensor base

Terminals (no polarity, two-wire)



1: L2 (connected to the common terminal)



2: L1 (connected to a lower-level device)



3: L1 (connected to an upper-level device)



4: reserved

Use a multimeter to check whether there is any short circuit or open circuit.

Y => Rectify the connection fault.

Check whether the fault is rectified.



If yes, no further action is required.



If no, contact Huawei technical support.

N => Contact Huawei technical support.

----End

6.2 Heat Detector Fault

Possible Causes



The power supply to the heat detector is abnormal.



The heat detector is faulty.



The cable connection of the heat detector is abnormal.

Tools and Materials



Multimeter

Summary of Contents for IDS1000




































































Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands

Huawei IDS1000, User Manual

Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands