HPE ProLiant e910 User And Maintenance Manual Download Page 167

Page: 167 / 182

11. Install the air baffle.

•

1U server blade air baffle

•

2U server blade air baffle

12. For 2U server blade, install the top cover.

13. Install the server blade in the chassis.

14. Power up the server blade.

Removing and replacing the system board

Removing the system board

Prerequisites

Before you perform this procedure, make sure that you have a T-15 Torx screwdriver available.

Procedure

1. Power down the server blade.

2. Remove the server blade from the chassis.

3. For 2U server blade, remove the top cover.

4. Remove the air baffle:

•

1U server blade air baffle

•

2U server blade air baffle

5. Remove all DIMMs.

6. If installed, remove these options from the system board.

Removal and replacement procedures

167

Summary of Contents for ProLiant e910























































































































































































Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands

HPE ProLiant e910, User And Maintenance Manual

Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands